Commercial Cylinder Warranty Terms and Conditions
This sets out the voluntary manufacturer warranty provided by Mixergy Ltd for eligible Mixergy products installed in the United Kingdom. This warranty is in addition to, and does not affect, your statutory rights under applicable consumer law, including the Consumer Rights Act 2015 if applicable.
1. What this warranty covers
Subject to the terms, conditions and exclusions below, Mixergy warrants that during the relevant warranty period the covered components will be free from corrosion, material defects and manufacturing faults.
This warranty applies to the following products:
MX-300-COM-576
MX-400-COM-750
MX-500-COM-750
MX-800-COM-990
MX-1125-COM-990
MX-2000-COM-1290
Plus any Mixergy domestic cylinder used in a commercial application subject to section 6 below.
2. Warranty periods
Warranty length depends on the component and, where stated, whether the product has been registered using the Mixergy Warranty Registration Form within 60 days of commissioning.
Failure to register does not affect your statutory rights but may affect eligibility for extended warranty periods offered by Mixergy.
Mixergy
Stainless Steel Cylinder (Inner Vessel, Inc. Sensor Strip):
• 25 years with registration
• 2 years without registration
Coverage applies to corrosion and material defects for potable mains water systems only, unless otherwise agreed in writing.
Mixergy Controllers & Electronics (All Products): 2 years standard
Includes, but not limited to:
- Mixergy Controller
- Mixergy Gauge
- Embedded Solar Diverter (where factory fitted)
- Heat Pump Controller (if applicable)
- PV Switch Controller (if applicable)
Ancillary Components (All Products): 2 years standard
Includes, but not limited to:
- Top-Up Pump
- Immersion Heaters
- Expansion Vessels
- T&P Valve
- Inlet Control Group (or appropriate inlet valve supplied for cylinders of 800L to 2000L)
- Heat Pump Kit Plate Heat Exchanger and isolation valves
- Heat Pump Kit Plate Heat Exchanger pump
Replacement parts or replacement appliances supplied under this warranty are covered for the remainder of the original warranty period only.
3. Transferability
This warranty may be transferred to a subsequent building owner, provided that the service history and commissioning documentation are retained and passed to the new owner.
4. Conditions of warranty
This warranty remains valid provided that:
• Installation is completed by a competent person in accordance with UK Building Regulations and the Mixergy installation instructions.
• The Benchmark commissioning checklist is completed and retained (this is in the rear of the Mixergy installation instructions).
• An annual service is carried out and documented (by a competent person who is registered with a competent persons scheme).
Warranty claims may be refused where a failure is directly attributable to lack of required servicing.
• The product has not been altered, misused, neglected, exposed to frost, excessive temperature, or unsuitable water chemistry.
• Water chemistry remains within recommended limits (including chloride levels below 300 ppm).
In areas where water hardness exceeds 200 ppm CaCO₃, an appropriate water treatment system must be installed for corrosion-related claims to remain valid.
5. Warranty start date and proof
The warranty start date will be determined by the earliest applicable of the following:
• Original proof of purchase
• Completed Benchmark form (Found in the installation manual)
• Date appliance first came online in the Mixergy IO database
If none of the above evidence is available, the warranty start date may be calculated as up to 9 months after the product passed final production testing. This does not affect statutory rights.
6. Exclusions and limitations
This voluntary warranty does not cover:
• Products installed outside the United Kingdom
• Installations not carried out in accordance with Mixergy instructions
• Failures caused by scale, water quality issues or third-party components not supplied by Mixergy
• Labour and access costs unless expressly agreed in writing
Where a domestic cylinder is used within a commercial environment, it must be supplied and fitted with a Mixergy Commercial Upgrade Kit, purchased separately, for this warranty to apply. A Mixergy Commercial Upgrade Kit includes a titanium immersion heater and a commercial label.
Nothing in this warranty excludes or limits liability for death or personal injury caused by negligence, fraud or fraudulent misrepresentation, or any liability which cannot be excluded or limited under applicable law.
This exclusion of consequential or indirect losses applies only to this voluntary manufacturer warranty and does not affect statutory rights.
7. How to make a warranty claim
To make a claim, please provide:
• Product MX number
• Proof of installation and service history
• Photos and description of the issue
8. Governing law
These terms are governed by the laws of England and Wales and are subject to the exclusive jurisdiction of the courts of England and Wales.